Page 1 of 2

Looking for a replacement cylinder for my pump

Posted: Wed Oct 31, 2018 5:15 pm
by Cajun Jeff
The one that came with my pump I think is 2 in. I need one a bit smaller this one keeps trying to suck in a nut. Not fun. Ouch. It’s elect and fits on the top of the tube.

Any help would be appreciated.

Re: Looking for a replacement cylinder for my pump

Posted: Thu Nov 01, 2018 2:31 pm
by 60s_surfer
I know of two possible solutions that don't require a new cylinder. On the UandMeTime Web site, there is a disk with a hole in the middle that fits over your erection and then the cylinder pushes the flat part of the disk up against your abdomen. You need to lubricate both sides of the disk to get a good seal. The other possibility depends on the exact size of your cylinder. The Timm Medical Web site has an insert that goes inside the cylinder to reduce the inner diameter. I believe it is for a cylinder with 2 inches inside diameter. Timm Medical sells the Osbone pump and constriction rings.

Re: Looking for a replacement cylinder for my pump

Posted: Thu Nov 01, 2018 8:04 pm
by Cajun Jeff
Thanks

Re: Looking for a replacement cylinder for my pump

Posted: Sun Nov 04, 2018 2:54 pm
by dtwarren1942
If your pump uses a standard male connector, LeLuv offers a decent quality cylinder with a wide base rim for comfort for about $30.

Cylinder sizing according to,LAPump

Girth —---> Cylinder Diameter
3.50 to 4.50* --> 1.50
4.75 to 5.25* --> 1.75
5.50 to 6.00* --> 2.00
6.25 to 6.75* --> 2.25
7.00 to 7.50* --> 2.50
7.75 to 8.25* --> 2.75

Re: Looking for a replacement cylinder for my pump

Posted: Mon Nov 05, 2018 11:26 pm
by JimStars
CJ,

The main thing is, ALWAYS be holding onto your nuts when pumping -- stretching scrotum down a bit -- keeping it that way until you slip on the rings. If not using rings and just keeping suction for a while -- well you will just have to judge if they be sucking back into cylinder. With an electric pump it is pretty easy to do pump and hold em with other hand.

J

Re: Looking for a replacement cylinder for my pump

Posted: Wed Nov 07, 2018 9:53 pm
by Cajun Jeff
Will try that. What I have done is start with low suction. Get the blood moving. Then add more pressure. After several rounds I can get to full suction. What I am searching far is a cylinder that does not allow girth but pulls for length.

Re: Looking for a replacement cylinder for my pump

Posted: Thu Nov 08, 2018 8:54 pm
by dtwarren1942
I have a 2.25” cylinder which I use occasionally, but it does invariably suck in my right Testicle after five minutes or so. I recently carefully slipped on a doubled over 1/2 inch wide elastic band over my balls, Just under the base of my shaft. I used a lot of lube on my balls and the band. And, it prevent my ball from being sucked up.

Re: Looking for a replacement cylinder for my pump

Posted: Fri Nov 09, 2018 10:15 pm
by Cajun Jeff
No exactly what you Man about 1/2 inch elastic band. Where do you get that?

Re: Looking for a replacement cylinder for my pump

Posted: Sat Nov 10, 2018 4:52 pm
by dtwarren1942
Cajun Jeff wrote:No exactly what you Man about 1/2 inch elastic band. Where do you get that?


1/2 inch is a standard size rubber/elastic band available at stationary section of any big box store or Staples. You can probably get a bag of 100 for about $1.

Re: Looking for a replacement cylinder for my pump

Posted: Mon Nov 12, 2018 9:46 am
by Cajun Jeff
Perfect you guys are so creative. Will pick some up today.