Fast question - wider VED tube needed

[Magic Rat]

I purchased an Encore Deluxe a while ago: https://www.amazon.com/Encore-Deluxe-Va ... op?ie=UTF8

I didn't really use it until recently. What Ive found is that I have quite a bit more girth than the standard tube they provided (1.75"). In looking over their website, they do provide a 2" version. I suspect I will need something wider, like a 2.5" - I'm pretty squashed inside the 1.75" and feel like it's so constricting I can't actually expand to full size when I pump (it's also uncomfortable).

I'm thinking of simply buying a whole new rig since the Encore doesn't seem to have a proper sized tube for me. Anyone have any recommendations for a VED system that can accommodate a girthier unit?

[bldoink]

When you're fully boned out with an injection what is your girth?

[ED BLOWS]

[quote="Magic Rat"]I purchased an Encore Deluxe a while ago: https://www.amazon.com/Encore-Deluxe-Va ... op?ie=UTF8

I didn't really use it until recently. What Ive found is that I have quite a bit more girth than the standard tube they provided (1.75"). In looking over their website, they do provide a 2" version. I suspect I will need something wider, like a 2.5" - I'm pretty squashed inside the 1.75" and feel like it's so constricting I can't actually expand to full size when I pump (it's also uncomfortable).

I'm thinking of simply buying a whole new rig since the Encore doesn't seem to have a proper sized tube for me. Anyone have any recommendations for a VED system that can accommodate a girthier unit?[/quot

I just ran into the same problem. Never bought a pump before, so I pretty much read every post in the pump section. lol. I ended up purchasing the SomaerectStf based off of Geronimos success. I am a little over “7 around fully erect so I ordered the 2.50 wide tube as a side order after figuring out the tubes supplied were restricting full bone out. Tried out the new tube today, played with the rings, ended up using two at one time (also suggested) in these threads and boom. Off to the races. Not bad for 30 min of tinkering around.

I would have probably thrown that thing in the trash if it weren’t for the many fellows that contribute in this section. With a little more practice I’m thinking it probably will go even better.

[Magic Rat]

When you're fully boned out with an injection what is your girth?

Measured at about 6 1/4". Maybe I don't quite need a 2.5" tube, but I'm thinking 2" might still be a little tight.

Should the erection be pushed against the sides tightly, or "roaming free" in the middle of the tube?

[Spontaneous1]

Get the 2.5".

[bldoink]

Too big will be uncomfortable and more difficult to get a seal. I'd go with the 2". It will just a little tight when pumped but that's what lube is for. But whatever, I'm not the resident VED expert.

[oldog12]

Kodi Distribution whose online is LeLuv

[AnotherOldMan]

Circumference = pi x d
C = 3.14 x 1.75" =5.5"
C= 3.14 x 2" = 6.28"
C = 3.14 x 2.5" = 7.85"

[dtwarren1942]

Cylinder sizing chart

Girth —---> Cylinder Diameter
3.50 to 4.50* --> 1.50
4.75 to 5.25* --> 1.75
5.50 to 6.00* --> 2.00
6.25 to 6.75* --> 2.25
7.00 to 7.50* --> 2.50
7.75 to 8.25* --> 2.75

[oldog12]

I have about a 6.5 in circumference and the 2.5 in cylinder is comfortable. A 2.25 in cylinder is not comfortable for me.