Needle Length

[zachcrane]

Ive been using 1/2inch Needle 30gauge and there is always discomfort when injecting on the 3 and 9 o'clock sides. I tend to inject very very slowly. It seems to take me a minute to insert the entire thing.

Do I just have a very thick cavernosa causing the discomfort? Its not pain but it definitely feels like something is going through it.

I tried using 5/16 and there is no discomfort but haven't had as good of erections.

Does anyone else have this same issue? I haven't tried injecting anywhere other than 3pm and 9pm.

Also my erections always seem to last 4-5 hours when I do them right and i'm only using 5 units. Do you think I would find success with 2 or 3 units for less than 4 hours? OR is my mix too strong?

My mix is PAP 30 / PHE 1/ PGE 25

[Leebert]

You might try dropping down to 30/1/10, it's the weakest strength of tri mix and see if that at least cuts time in half, but not sure if it will affect hardness or not. I'm on 30/2/50 and it's not working well at all and not sure what to do with that! Anyhow see if that works. The injections are a trial and error, patience ( which can get thin) and mentally draining until you get it right if you can.

[Leebert]

Another thing, I use 31g, 5/16 and when sticking my dick I just kind of jiggle it in until I get into the CC.

[ShouldIwait]

could switch to bimix...not as strong and does not need to be refrigerated!

[bldoink]

Use whatever length works best for you. I use 31 gauge 5/16". When using the 5/16" I insert the whole length of the needle plus indent myself with the plastic nub of the needle syringe. Also make sure you use the .3cc (1/3cc) volume syringes for such a small dose.

You may also want to consider buying some bacteriostatic water and diluting your mix, if you feel comfortable doing that. You might want to consult your pharmacist if needed.

[notaes]

I learned very quickly that my pharmacists was a great source of info regarding lots of things. Needle length was one of those things. He talks to a lot of folks about what works best etc. He is a great trusted friend also. Highly recommend talking to one you really like and developing a good relationship with him/her.

[zachcrane]

could switch to bimix...not as strong and does not need to be refrigerated!

Here's a thought I had. If the Alprostadil/PGE1 is what's causing the ache couldn't I turn the Trimix into Bimix by leaving it out at room temp?

I think that's the only ingredient that needs to be kept refrigerated in order to work. Otherwise you just have bimix correct?

I currently have 10ML of the trimix formula so I guess I'd want to be certain its the PGE1 that is causing the ache so I could fill a syringe and leave it out for a few days and then test to see it if works?

[bldoink]

could switch to bimix...not as strong and does not need to be refrigerated!

Here's a thought I had. If the Alprostadil/PGE1 is what's causing the ache couldn't I turn the Trimix into Bimix by leaving it out at room temp?

I think that's the only ingredient that needs to be kept refrigerated in order to work. Otherwise you just have bimix correct?

I currently have 10ML of the trimix formula so I guess I'd want to be certain its the PGE1 that is causing the ache so I could fill a syringe and leave it out for a few days and then test to see it if works?

That might work to some degree but I think I'd be a bit concerned about bacteria growth leaving it out for an extended time. There's also the consideration of the Alprostadil being the most potent ingredient. Also some research has suggested that the Alprostadil is the ingredient least likely to cause dick damage.