Anyone prefer pumps, and what size rings and sleeves

[JimStars]

Wondering if THIS can possibly fit thru THAT .. (No2 Sleeve)

can_it_possibly_fit.png (243.82 KiB) Viewed 4636 times

[JimStars]

Yes it can .. everybody's squeezable... to a point.

yes_it_can_fit.png (219.62 KiB) Viewed 4625 times

[JimStars]

Drumroll please ... the final result using No2 Sleeve and B-ring.

Please note .. as compared to next image ,, the tighter fit of No2 sleeve reduces length and girth a little bit .. but still rock hard. Also notice the length of the sleeve .. 1" here and 2" on the extended. So with more shaft 'exposed' above the shorter sleeve it may just look longer -- which is an OK way to look!

retake_No2_b_ring.jpg (149.51 KiB) Viewed 4563 times

[JimStars]

Using The No3 Ext Sleeve -- an inch more length and more girth.
That might be too much for some gals!

final_result_no3ext_sleeve_b_ring.jpg (143.62 KiB) Viewed 4666 times

[palace01]

I didn't see anybody reply on 1" versus 2" preference ?
BillyBob - I have similar measurements to you (always thought my girth small but length good) - did you decide on #2 or #3?
JimStars - NICE PICS BUT - do you have to 'somehow' squeeze the penis or stretch the sleeve ? Difficult???

[JimStars]

Palace,

On squeezing into the sleeve... while flaccid and lubed with Astroglide or other lube any size penis can surely squeeze into at least one of the three sleeve sizes -- like oozing thru like putty! The VED pump then does the rest. The sleeve may stretch a tiny bit when pumped to max vacuum.

I use the larger tube that you can buy for an Encore pump. It is 2" ID and has enough room for penis, sleeve and even rings if you like to slip them off the outside of the tube and then make a good seal and pump more.

J

[palace01]

Thanks Jim..

[mmartinez]

Thx, guys, for the input. I am def not huge, but I have measured several times, and get a bit over 4 flacid and 6 or so pumped(just measured that once). I didn't know measuring was rocket science, guess I will try it again, since that 4+ flacid puts me over the maximum size Osbon(7/8"?), and way over the largest(Z) that came with my Augusta(0.5"). I simply can not be all that fat! I think of myself as maybe average girth and a tad less than average length. Anyway, I went ahead and ordered Osbon Medium, High Tension - Inside Diameter 3/4 Inch (0.75) #D

I still have not ordered the sleeve. What do you think: the #2(up to 4.5 girth) at 1" length? 2" length?
Bill

-----
Hi
I was wondering if you had success with the "Osborne Medium, High Tension #D?
I am about to order one, same size, same situation, same equipment as you.
Thank You
Mario

[JimStars]

Mario,

Yes the Osborne Medium, High Tension #D (pink) is a real workhorse tension ring. It is possible that will be all you need as it will be very tight.

But I would normally use it with a Large Standard A (Beige) .. or even a Medium Standard Tension C (Beige) ....

You will probably find, like everyone else, that you really need two bands to keep things hard for 10+ minutes in a really unforgiving environment!!!

Any combo of Pink and Beige is pretty good. Pink+Pink would get pretty uncomfortable.

J

[mmartinez]

Mario,

Yes the Osborne Medium, High Tension #D (pink) is a real workhorse tension ring. It is possible that will be all you need as it will be very tight.

But I would normally use it with a Large Standard A (Beige) .. or even a Medium Standard Tension C (Beige) ....

You will probably find, like everyone else, that you really need two bands to keep things hard for 10+ minutes in a really unforgiving environment!!!

Any combo of Pink and Beige is pretty good. Pink+Pink would get pretty uncomfortable.

J

================
Thank you for the reply Jim,
So you use the sleeve and 2 rings ?
I am just about to start using the pump and until I read this post, I never new you could use 2 rings.
When you transfer the rings to the shaft, both rings slip at the same time? Or one after the other?
The rings will fall on the sleeve?
Thank you for for your help
Mario